The Basics of Plumbing Skills for Bathtub Installation
The Basics of Plumbing Skills for Bathtub Installation
Blog Article
How do you actually feel with regards to Installing A Bathtub?
Setting up a bathtub isn't precisely rocket science, but it does need solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a moderately tough job. If the old bathtub is readily accessible, the project can move easily; if you have to open a wall surface to eliminate the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the job is within a house handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as embeded in the new one. Make certain you have actually qualified on your own for the work and are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is much better to think about utilizing one before you begin. Chances are you might need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your bathroom if you have currently acquired a brand-new tub and don't require to change the arrangement of your previous water pipes.
Your tools and also material list ought to make up the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath needs to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps device to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of the two taps making use of 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your installment, then the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing taps can be quite problematic as a result of the restricted access that is commonly the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been removed, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any old securing substance.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Making use of both wooden boards under its feet, place the bath tub in the called for setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the spirit level and readjusting the feet on the tub till the spirit level reads level.
To mount faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water system as well as inspect all joints and also new pipework for leaks and also tighten them if necessary. Fill the tub and also examine the overflow outlet and the regular electrical outlet for leaks.
Finally, take care of the bath paneling as defined in the manufacturer's user's manual. Tiling and securing around the bathtub should wait till the tub has been utilized at the very least when as this will certainly resolve it into its last setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin making certain that the washers remain in location between the faucet as well as the sink. Protect the faucet in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with normal tap adapters. The previous type must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, creating the water to penetrate the wall in between the bath as well as the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and installations. They are offered in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always load the bath tub with water prior to sealing, to permit the activity experienced when the bathtub remains in usage. The sealant can break relatively early if you do not consider this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also quickly available on the market. It is advisable to fit the tiles making use of waterproof or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
I hope you enjoyed our section on Tools You Need to Install a New Bathtub . Thanks so much for taking time to read our blog. Sharing is good. You won't know, you might be helping someone out. Thank you for your time. Visit again soon.
Act fast, call! Report this page